$78.90
$72.59
5PCS 3D Printer Parts TMC5160 V1.2 SPI Stepper Motor Driver S5160 Stepstick Mute Driver Flying Wire For F6 Board VS TMC2130 V1.2 Features: Hardware compatible with StepStick and Pololu A4988...
5PCS 3D Printer Parts TMC5160 V1.2 SPI Stepper Motor Driver S5160 Stepstick Mute Driver Flying Wire For F6 Board VS TMC2130 V1.2 Features: Hardware compatible with StepStick and Pololu A4988...

FREE
SHIPPING

100% MONEY
BACK GUARANTEE

ONLINE
SUPPORT 24/7

FREE
SHIPPING

100% MONEY
BACK GUARANTEE

ONLINE
SUPPORT 24/7

Availability: 95 In Stock

5PCS 3D Printer Parts TMC5160 V1.2 SPI Stepper Motor Driver S5160 Stepstick Mute Driver Flying Wire For F6 Board VS TMC2130 V1.2

01

Features:
Hardware compatible with StepStick and Pololu A4988 Stepper Motor Drivers
stepper motor driver (chopper drive / constant current drive)
Components on the bottom PCB side for better heat emission
Automatic standby current reduction
microPlyer - microstep interpolator for increased smoothness of microstepping
stealthChop - for quiet operation and smooth motion
spreadCycle - highly dynamic motor control chopper
Drive capability up to 3A (RMS) continuous coil current
Step/Dir interface with up to 256 microsteps
SPI interface for configuration
Motor supply voltage: 10...35V
Logic supply voltage: 3.3...5V
RSense: 0.075 Ohm
 
What is the difference between TMC5160 and TMC2130 SilentStepSticks?
TMC5160 SilentStepSticks have no standalone mode and no internal pull-up resistor on the CS/SS pin. (SPI configuration is always needed)
The direction is not inverted on TMC5160 SilentStepSticks.
The software configuration is mostly the same, except the motor current calculation is different.
TMC5160 SilentStepSticks have an improved stealthChop mode (stealthChop2) and a higher motor current rating.
On TMC5160 SilentStepStick v1.3 the CLK pin has to be connected to GND.
 
Extra features of TMC2130:
SPI configuration interface (up to 4MHz)
up to 256 native microsteps (without interpolation)
coolStep - current control for energy savings
stallGuard2 - sensorless motor load detection
dcStep - load dependent speed control
Automatic stealthChop and spreadCycle switchover depending on velocity
 
Note:
This version is not required to be wired. It is used on the F6 board. We will provide the wiring version for other boards. Please pay attention to our shop or our facebook.
https://www.facebook.com/groups/197476557529090/?ref=bookmarks
 
Package listing:
5*TMC5160 V1.2
5*heatsink

02

If you want F6 V1.3,pls clip the picture:

_DSC1513

 

IMG_9984IMG_9985IMG_9995IMG_9986IMG_9987IMG_9988IMG_9996IMG_9997

 

 

 

5PCS 3D Printer Parts TMC5160 V1.2 SPI Stepper Motor Driver S5160 Stepstick Mute Driver Flying Wire For F6 Board VS TMC2130 V1.2

01

Features:
Hardware compatible with StepStick and Pololu A4988 Stepper Motor Drivers
stepper motor driver (chopper drive / constant current drive)
Components on the bottom PCB side for better heat emission
Automatic standby current reduction
microPlyer - microstep interpolator for increased smoothness of microstepping
stealthChop - for quiet operation and smooth motion
spreadCycle - highly dynamic motor control chopper
Drive capability up to 3A (RMS) continuous coil current
Step/Dir interface with up to 256 microsteps
SPI interface for configuration
Motor supply voltage: 10...35V
Logic supply voltage: 3.3...5V
RSense: 0.075 Ohm
 
What is the difference between TMC5160 and TMC2130 SilentStepSticks?
TMC5160 SilentStepSticks have no standalone mode and no internal pull-up resistor on the CS/SS pin. (SPI configuration is always needed)
The direction is not inverted on TMC5160 SilentStepSticks.
The software configuration is mostly the same, except the motor current calculation is different.
TMC5160 SilentStepSticks have an improved stealthChop mode (stealthChop2) and a higher motor current rating.
On TMC5160 SilentStepStick v1.3 the CLK pin has to be connected to GND.
 
Extra features of TMC2130:
SPI configuration interface (up to 4MHz)
up to 256 native microsteps (without interpolation)
coolStep - current control for energy savings
stallGuard2 - sensorless motor load detection
dcStep - load dependent speed control
Automatic stealthChop and spreadCycle switchover depending on velocity
 
Note:
This version is not required to be wired. It is used on the F6 board. We will provide the wiring version for other boards. Please pay attention to our shop or our facebook.
https://www.facebook.com/groups/197476557529090/?ref=bookmarks
 
Package listing:
5*TMC5160 V1.2
5*heatsink

02

If you want F6 V1.3,pls clip the picture:

_DSC1513

 

IMG_9984IMG_9985IMG_9995IMG_9986IMG_9987IMG_9988IMG_9996IMG_9997

 

 

 

size chest(in.) waist(in.) hips(in.)
XS 34-36 27-29 34.5-36.5
S 36-38 29-31 36.5-38.5
M 38-40 31-33 38.5-40.5
L 40-42 33-36 40.5-43.5
XL 42-45 36-40 43.5-47.5
XXL 45-48 40-44 47.5-51.5
size chest(in.) waist(in.) hips(in.)
XS 34-36 27-29 34.5-36.5
S 36-38 29-31 36.5-38.5
M 38-40 31-33 38.5-40.5
L 40-42 33-36 40.5-43.5
XL 42-45 36-40 43.5-47.5
XXL 45-48 40-44 47.5-51.5
Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat.
Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat.