::: coupon 有效期：ccoupon 适用条件： 金额：10 $ 券码：X3GAKNXGPNPE ::: !!! note New website for downloading A1 sealed carton printouts: https://www.thingiverse.com/thing:7091008 New website for downloading AMS sealed carton printouts: https://www.thingiverse.com/thing:7091007 !!! ## Printer box sealing - **Applicable models:** A1/A1MINI, SV07, Ender3, Prusa, etc. And machines with a width of less than 490mm, a depth of less than 520mm, and a height of less than 600mm in the space required for movement - **Dimensions and weight description:** The outer dimensions of the box are: 603×603×606MM with an error of ±2mm, and the total weight is 11kg. ### Features: (1) Strong compatibility; Applicable to a variety of machines (2) Dustproof and heat-insulating; Sealed box can effectively prevent dust and keep warm (3) Noise reduction and sound reduction; Fully enclosed box can greatly isolate the noise of the machine (4) Real-time monitoring of temperature and humidity; A temperature and humidity detector is equipped to monitor the temperature and humidity inside the box in real time (5) The cover has good light transmittance; the box uses transparent acrylic as the sealing plate, and the light transmittance of the entire box is not affected (6) Built-in LED light; The box printing piece is equipped with a reserved LED light strip for fill light, and the customer can install the light strip as needed. The switch can adjust the brightness, and customers can adjust it according to their own observations. (7) Humanized design; full print design, customers can DIY the inside of the sealed box according to their own needs (8) Equipped with air filter; air filter is configured in the sealed box, no need to worry about the invasion of toxic gases !!! note Due to compatibility with too many machines, some customized installations or personalized prints of some specific machines are not included in the kit, and customers need to DIY print them themselves; the currently configured prints are only for the A1/A1MINI series. !!! ### T station print link: https://www.thingiverse.com/thing:7003986 ## AMS Sealing ### Scope of application: AMS lite ### Main components: acrylic board, desiccant, temperature and humidity sensor, 3D printed parts, etc. **Dimensions:** 314mm long x 611mm wide x 328mm high ### Features: * Visible, transparent, environmentally friendly and heat-resistant material: observe the consumables in real time anytime and anywhere, and also have the function of sealing and isolation; * Built-in drying box, dehumidification can be performed during internal circulation. The dehumidification material is environmentally friendly and recyclable (3~4 times); * Configured with a digital display thermometer and hygrometer, you can keep track of the temperature and humidity in the box at any time; * Storage of consumables: The closed storage space can keep the consumables clean and tidy, dust-proof and moisture-proof, and safe and scald-proof; * High safety and high compatibility: High safety, wide compatibility, compatible with most models and consumables on the market, and can be used with various consumables, such as PLA, ABS, PETG, PVA, ePA, ePA-CF, ePA-GF, PC, TPU-95A, etc. * Compatible material roll: diameter about 200mm, mass 1kg; --- ### Operation method and precautions for regeneration of dry silica gel #### a. Operation method for regeneration of dry silica gel ① Heat directly in the pot with the lowest heat. It is recommended to use a frying pan. It will turn back to blue in about 3-5 minutes. Disadvantages: Most of it will break after heating. It is recommended to use a dispensing bag to pack it, and the broken parts will not leak out. ② Microwave heating, it is recommended to use a low gear, it will turn back to blue in about 20 minutes. It is recommended to heat it several times to release the water vapor in the microwave. Disadvantages: Most of it will break after heating. It is recommended to use a dispensing bag to pack it, and the broken parts will not leak out. ③ Oven heating, the heating temperature is set to 100 degrees, it is recommended to use a plate or other utensils so that it can be heated over a large area, and it will turn back to blue in 40 minutes. **Disadvantages:** The heating time is too long. **Advantages:** The blue silica gel will not break during the heating process, and this method is recommended. --- #### b. Precautions ① During drying and regeneration, the temperature should be gradually increased to avoid the explosion of the rubber particles caused by intense drying, which will reduce the recovery rate. ② When the silica gel is roasted and regenerated, too high a temperature will cause changes in the pore structure of the silica gel and significantly reduce its adsorption effect, affecting its use value. For blue gel indicators or color-changing silica gel, the desorption and regeneration temperature should not exceed 120°C, otherwise the color developer will gradually oxidize and lose its color development effect. ③ The regenerated silica gel should generally be sieved to remove fine particles to make the particles uniform. ### Product print link: https://www.thingiverse.com/thing:6994254/files ### Precautions: Desiccant is a chemical substance and is inedible. If ingested by mistake, please seek medical attention in time; Dry silica gel particles have strong moisture absorption capacity, so they should be stored in a dry place, and there should be a shelf between the packaging and the ground. The packaging includes steel drums, paper drums, cartons, plastic bottles, polyethylene plastic composite bags, flexible container bags, etc. During transportation, rain, moisture and exposure should be avoided.