Universal Parts

Product Introduction The E4 board is a minimal 3D printer control board based on the ESP32 microcontroller from ESPRESSIF, with built-in Wi-Fi and Bluetooth. The controller speed is up to 240MHz, 16M flash. Features Compact size: 90mm x 67mm Native Wi-Fi support 12V to...

Introduction The FYSETC SD-WIFI is a module that can run ESPwebDev（https://github.com/ardyesp/ESPWebDAV）.We made it into the shape of an SD card so it can be directly inserted into an existing SD card slot and powered.You can connect it to the router using the serial command...

Features Based on STM32F072 Type-C USB socket Supports CAN2.0A and B, baud rates up to 1M Compatible with CANable Support with CAnable / CandleLight / Klipper firmware 3-pin screw terminal: CANH, CANL, GND Jumper to enter bootloader for firmware updates Onboard 120R termination default...

Features Mini12864LCD has 6 styles, the variety of styles to choose a more professional service for your machine A. RGB backlight black B. RGB backlight white C. Black on white D. White on black E. White on blue F. Black on Green Designed for...

About the Product H36 Combo V1 is a newly designed high temperature tool board running Klipper firmware. Based on STMG0B1T3, the maximum operating temperature can reach 125 degrees Celsius (CAN only). It also provides two communication methods: CANBUS and USB. The onboard USBHUB has...

Warning If you use 48V to power the VMOT of the module and 24V step-down to power the VIO, please make sure that 48V and 24V are turned on at the same time (that is, VMOT and VIO arrive at the same time). Otherwise,...

Feature High-speed DPI interface 4.0“ IPS (wide viewing angle, 160°) display (86.4x51.8mm) 800x480 pixels (~235 PPI) 18-bit colour (262,144 colours)/18（26） 60 FPS frame rate/60 Contrast ratio: 500:1 Capacitive touch 5V@3A DC-DC onboard(9-28V input)/5V/3A DC-DC（28V） 40-pin female header included /40pin Standoffs included Compatible with all...

About the Product ： It can replace the bracket accessories of the all-metal Sherpa extruder. The bracket has an extra hole to make the extruder more stable.

About the Product A RP2040 Based powerful XY Stepper Motor Driver module with CAN/CANFD Interface Features up to 133Mhz MCU RP2040 Dual 6.0A MAX onboard TMC5160 Drivers with heatsink 48V & 24V Input 12V5V/3.3V DC-DC Convertor CANFD Support based on MCP2518 Klipper & RRF...

About the Product This High Flow Nozzle uses a unique custom internal geometry to increase the surface area for improved thermal transfer to the filament.And increases your setup’s volumetric flow rate, enabling you to print faster. The Nozzle is a preassembled nozzle and HeatBreak...

Overview FYSETC 5 inch DSI capacitive touch screen for Raspberry Pi uses an 800 × 480 IPS display, DSI interface, 5-point touch, 160° viewing angle, and 120 mm × 75 mm panel size for Klipper-style control displays. Compatibility Raspberry Pi 5, 4B, CM4, 3B+,...

Star Shaped Inner Wall Design This PTFE tube features a unique flower pattern or star shaped cross section. The concave convex design significantly reduces contact area between filament and tube wall, lowering friction resistance by 30 percent compared to traditional round tubes. Low Friction...

Star Shaped Inner Wall Reduces Friction by 30% This PTFE tube features a unique flower pattern or star shaped cross section. The concave convex design significantly reduces contact area between filament and tube wall, lowering friction resistance by approximately 30% compared to traditional round...

Overview This luminous hydraulic bearing fan adds cooling airflow and LED lighting for 3D printer heatsinks. The images show 2510, 3010, and 4010 fan sizes, 12V/24V options, multiple LED colors, low-noise hydraulic bearings, and a 3 cm cable. Compatibility Not machine-specific; suitable for 3D...

Pure Mechanical Filament Protection This filament cutter is a purely mechanical accessory that detects filament tangles and knots through tension. When the extruder pulls on a stuck filament, the internal mechanism converts the pulling force into shearing force and cuts the filament instantly. No...

2-in-1 Dual Filament Input for Single Hotend This Y splitter combines two filament sources into one output, allowing you to print dual color or gradient models on a single extruder printer. No need for a dual extruder hotend to achieve multi-color effects. Smooth Anti-Clog...

Universal Fit 40-68cm Adjustable Width The width and depth are both adjustable between 40-68cm, fitting most 3D printers on the market including Bambu Lab X1/P1/H2, Creality K1/Ender, Anycubic Kobra, and Prusa series. No need to guess compatibility. Dual Mode Design for Mobility and Stability...

Overview Hv5160 is speciaal ontworpen voor hoge spanning drive eisen en kan werken in de spanning bereik van 8-60v, zoals 48V. De 100V X7R 0805 keramische condensator gebaseerd op tmc5160-wa en Samsung Electronics is ontworpen. 1000 x 600mil / 25.4x15.24mm 6 laag TG155 PCB...

Please note: The package contents do not include printed materials; you will need to print them yourself. HackMan3D Orbit Controller Build your own professional 6-DoF navigation controller for CAD, 3D modeling and creative applications. The HackMan3D Orbit Controller is a fully open-source DIY project...

Reliable PTFE Tube Connection for 3D Printers This PC4-M6 pneumatic connector securely holds 4mm OD PTFE tubes in place at extruders, hotends, and AMS hubs. Prevents tube loosening that can cause filament jams and failed prints. Durable PTFE Construction Heat Pressure Resistant Made from...