Exclusive Compatibility For CR-10 Smart Pro & Ender-5 S1 Printer Models Pre-matched terminal definition consistent with original factory circuit, direct plug replacement without pin rearrangement. Fixed 1.5M Total Length Meets Remote Extrusion Modification Demand Enough reserved length for hotend lifting and frame refit, eliminate...
0.2mm Ultra High Precision Printing Features a 0.2mm precision nozzle capable of printing extremely fine details and complex structures, ideal for jewelry design, figurines, miniatures, and other high precision applications. Hardened Steel Nozzle Wear Resistant Nozzle made of hardened steel with hardness far exceeding...
Complete Cooling System Replacement Includes all 4 types of fans for Anycubic Kobra S1 Combo: mainboard cooling, extruder blower, air filtration and motor cooling, one-stop solution for all thermal needs. 24V DC Standard Specification All fans are 24V DC powered, matching the printer’s original...
Raspberry Pi 5 inch DSI Touch Screen MIPI LCD V1.1 5 Inch LCD Touch Screen 800 X 480 DSI Display IPS Working With Raspberry Pi5/4B/CM4/3B+/3A+/3B/CM3/CM3+/2B/B+/A+
Raspberry Pi 5 inch DSI Touch Screen MIPI LCD V1.1 5 Inch LCD Touch Screen 800 X 480 DSI Display IPS Working With Raspberry Pi5/4B/CM4/3B+/3A+/3B/CM3/CM3+/2B/B+/A+
Raspberry Pi 5 inch DSI Touch Screen MIPI LCD V1.1 5 Inch LCD Touch Screen 800 X 480 DSI Display IPS Working With Raspberry Pi5/4B/CM4/3B+/3A+/3B/CM3/CM3+/2B/B+/A+
FYSETC 5 inch DSI capacitive touch screen for Raspberry Pi uses an 800 × 480 IPS display, DSI interface, 5-point touch, 160° viewing angle, and 120 mm × 75 mm panel size for Klipper-style control displays.
If you want to use this screen with a Raspberry Pi 5, you will need to build touch and backlight drivers for it. kkobold has taken the time to build them here:
https://github.com/kkobold/fysetc-5inch-dsi-touch
I can confirm it works. You will need a 22pin to 15pin DSI cable, I use the official RPi5 official display cable.
I had to configure proper dst overlays to get the screen working, but at-least it's compatible with Debian Trixie.
Screen doesn't support brightness adjustment although the vendor claims it to be.
Setting "/sys/class/backlight/rpi_backlight/brightness" to any value give no changes.
The only value that works, is "0", which turns off the display.
The touchscreen is not working as it should with the default configuration on RPi, a little fix is needed.
The touchscreen is working just fine after commenting out "dtoverlay=vc4-kms-v3d " in /boot/firmware/config.txt
More details at:
https://osoyoo.com/2019/09/20/instruction-for-raspberry-pi-5-dsi-touch-screen/
Exclusive Compatibility For CR-10 Smart Pro & Ender-5 S1 Printer Models Pre-matched terminal definition consistent with original factory circuit, direct plug replacement without pin rearrangement. Fixed 1.5M Total Length Meets Remote Extrusion Modification Demand Enough reserved length for hotend lifting and frame refit, eliminate...
0.2mm Ultra High Precision Printing Features a 0.2mm precision nozzle capable of printing extremely fine details and complex structures, ideal for jewelry design, figurines, miniatures, and other high precision applications. Hardened Steel Nozzle Wear Resistant Nozzle made of hardened steel with hardness far exceeding...
Complete Cooling System Replacement Includes all 4 types of fans for Anycubic Kobra S1 Combo: mainboard cooling, extruder blower, air filtration and motor cooling, one-stop solution for all thermal needs. 24V DC Standard Specification All fans are 24V DC powered, matching the printer’s original...